Made here.

Brackets, bent tube and formed parts, from the cut to the box. Then the heavy work. Every picture is our own shop floor.

• A sheet of metal on the cutting table with part outlines cut through it
• The torch cuts rows of slotted plates out of a steel sheet on the cutting table
• A torch throws sparks while cutting slotted plates from a sheet
• A grinder throws sparks across a cut part on the cutting table
• A length of steel clamped in the band saw
• A man works at the ironworker with stacks of punched angle on the bench
• A gloved hand holds a punched plate in front of a stack of bent angles
• A small plate sits on the die of the press brake under the punch
• A stack of bent plates held up at the press brake
• Stacks of formed plates on the press brake
• A welded setup with upright rods sitting in the press brake
• A row of formed steel brackets standing on the table
• Two rows of U shaped brackets on the table
• A group of bright gusset brackets standing on the fixture table
• Rows of gusset plates standing on base plates on the fixture table
• Formed sheet metal pieces with flanges on a bench
• Long formed sheet metal parts with tabs on the fixture table
• Bright formed stainless parts laid on the fixture table
• A stack of plates with a pressed dimple and stepped edges
• A stack of cut plates standing on the fixture table
• A row of short posts welded to base plates on the fixture table
• Formed channels stacked in a pyramid on the fixture table
• Long formed strips laid side by side on the fixture table
• Long formed channels running the length of the fixture table
• A length of tube clamped in the tube bender
• A bent tube lying on the fixture table
• A long bent tube lies on the fixture table beside a tape measure and a hammer
• Two fans of bent tube pieces laid out on the fixture table
• Two heavy bent tubes standing on the fixture table
• Bent tubes stacked on the fixture table
• Bent tubes with coped ends on the fixture table
• A bent tube arch lying on the shop floor
• Two hairpin bends in round bar on the shop floor
• A bent bar handle held against its paper template
• Four sets of thin bent stainless tubes laid out on the shop floor
• Sets of thin bent stainless tubes nested together on the floor
• A row of bent rods lined up on the bench
• A pile of bent D shaped handles on a table
• A single bent handle on the edge of a table
• A flat bar passes between the dies of the bar roller
• A bar curves through the roller while a man with white hair measures at the table behind
• A long bar rolled to a curve on the fixture table
• A stack of bent flat bar frames on the fixture table
• Bent flat bar frames stacked flat on the fixture table
• A man with a white beard stands at the milling machine over a plate with a square opening
• An end mill cuts a slot, with chips piled along the cut
• A milling machine stands in a hazy shop with sparks glowing behind it
• A welding arc lights up a part clamped to the fixture table
• A welder in a painted hood welds a part on the fixture table
• A welded steel frame with gussets and a curved plate on the fixture table
• A welded steel tube frame standing on the shop floor
• Calipers measure a formed part on the table
• Small bright brackets laid out on cardboard
• An open carton of bent tube parts on the shop floor
• Formed parts wrapped in film inside a wooden crate
• A man with white hair lifts a wooden crate frame beside bent tube parts on the table
• A welder in a hood works on a railing panel of round bar on the fixture table
• A man with white hair sets round bars into a rail on the fixture table
• A man in glasses fits bar to a long railing on the fixture table
• A man works on a steel railing panel with curved pickets standing on the fixture table
• A framed wire mesh panel hangs from the hoist on the shop floor
• Looking up at wire mesh welded into a bright tube frame
• A long perforated metal tray on stands runs down the shop
• A large welded steel frame hangs from a chain hoist in the shop
• Close view of a heavy steel frame with rows of holes and dome head fasteners
• An L shaped counter with a black steel base and a live edge wood top on the shop floor
• A welder in a hood works on curved stair parts laid out on the fixture table
• Two men work on long stair stringers laid across the fixture table
• A curved stair stringer held by a plate clamp on the fixture table
• Two men fit a steel beam on the fixture table while a stair section hangs from the hoist
• A welder in a hood works on a stair stringer hanging from a chain hoist
• Stair treads stacked up on the fixture table beside a rolling ladder
• Steel treads fitted to a curved stair on the fixture table
• The underside of a curved steel stair standing on the fixture table
• Two men stand up on a curved steel stair, fitting it
• Two men work on a curved steel stair with sparks flying
• A welding arc flares high up on the curved stair
• A welder in a hood sits up on the stair, welding
• Stair treads fixed to a stringer lying on the shop floor
• A steel stair section and a curved landing lying on the shop floor
• A wide view of the shop with steel channel laid out on the floor under the bridge crane
• The shop floor seen from above, with a welding arc lit in the middle